What Does Spd2 Mean On Whirlpool Microwave (2024)

FAQs

What Does Spd2 Mean On Whirlpool Microwave? ›

The "SPD1" or "SPD2" is just the microwave asking you to select if you want the fan on low speed or high speed. SPD1 is low fan speed, and SPD2 is on high fan speed. All you need to do is select which fan speed you want the fan to go on to wafter you press the vent fan button to turn the fan on.

High (“SPd2”), low (“SPd1”), and off. Comes on automatically as cooling fan during any cook function.

Good protection level. OVR type 2 and Type 2+3 are designed to protect electric installations and sensitive equipment against indirect surges with ensuring a low protection level (Up). It is characterized by its capacity to safely discharge current with 8/20 µs wave form.

The vent fan may be turned off at any time using the Vent Fan keypad. Touch OPTIONS/ CLOCK to reach the 30 Minute Fan Timer submenu and select the setting.

There may be a problem with the Keypad (User Interface) or the associated wiring. Power unit down by turning off the circuit breaker(s) for one (1) minute. Power unit up by turning on the circuit breaker(s). Monitor the microwave for one (1) minute to ensure the error code does not display again.

Type 1 SPDs are typically installed on the line side of the service entrance, offering protection from external surges and direct lightning strikes. Type 2 SPDs are installed on the load side of the service entrance or distribution panels, providing protection from internal surges and indirect lightning strikes.

A surge protective device (SPD) is designed to protect electrical systems and equipment from surge events by limiting transient voltages and diverting surge currents. Surges can originate externally, most intensely by lightning, or internally by the switching of electrical loads.

Depending on the temperature inside the microwave oven after a cooking cycle ends, the cooling fan may continue to run for some time in order to cool the microwave oven. The turntable may also continue to rotate and the light may stay on during this time. This is normal.

Keep the microwave unplugged for 5-10 minutes. The waiting period allows the internal components of the microwave to reset, ensuring a clean slate when you plug the microwave back in and reprogram your desired settings.

Where is the microwave reset button? ›

Most microwaves do not come with a reset button. However, there is an easy process to reset KitchenAid^® microwaves. Clear any display or error codes and unplug your microwave for one minute. After plugging it back in, attempt to heat one cup of cold water for two minutes at 100% cooking power.

Press and Hold “Start” and “Power” Buttons

Simultaneously press "Start" or "Pause" (depending on your model), and "Cancel" or“Power” buttons at the same time. Hold the buttons for about 5 seconds. Release the buttons and run a short cycle to check if the washer has been reset.

The "SPD1" or "SPD2" is just the microwave asking you to select if you want the fan on low speed or high speed. SPD1 is low fan speed, and SPD2 is on high fan speed. All you need to do is select which fan speed you want the fan to go on to wafter you press the vent fan button to turn the fan on. I'm glad I could help.

For those wondering why a microwave fan won't go off, some causes include: Overusing the microwave. Microwave thermostat or control board issues. A kitchen that's too hot or lacks ventilation.

All Over-the-Range Microwaves have an automatic fan feature to help protect the electronic components as well as help the cooking area get rid of excess heat. The built-in thermostat automatically turns the vent fan on if the appliance is too hot and will not turn off until the Microwave is cool again.

Convertible means it can vent through the wall or ceiling using a duct, or can be converted to non-venting (filters the air and blows it back into the kitchen) with Recirculation Kit Part Number W10294733 which is available from your dealer or an authorized parts distributor.

An externally vented microwave has a fan that pulls air through the microwave's vents and into an exhaust duct that leads to the outside of the building. This means that most of the moisture, heat, smell, and particles made by cooking go right outside.

Microwaves are shipped from the factory to vent out the top (vertically) but can also be vented out the rear (horizontally). The duct must be the sizes listed above for proper draw of air. Both smaller and larger vents than recommended decrease venting performance.